Featured Products

  1. 1 - 6 GHz High Linearity Gain Block Amplifiers: QPA9126 And QPA9127 11/8/2019

    Qorvo’s QPA9126 is a high linearity gain block amplifier providing very flat gain across a broad range of frequencies with the integration of a shut-down biasing capability to allow for operation for TDD applications. At 3.5 GHz, the QPA9126 amplifier provides 16 dB gain, +35.5 dBm OIP3 and 1.4 dB noise figure while drawing 70 mA current from a 5V supply. The QPA9127 amplifier provides 20 dB gain, +35.5 dBm OIP3 and 1.4 dB noise figure while drawing 70 mA current from a 5V supply at 3.5 GHz.

  2. 9 – 10.5 GHz GaN T/R Module: QPM2637 2/12/2019

    he QPM2637 is a Gallium Nitride MMIC front-end module (FEM) designed for X-Band radar applications within the 9-10.5 GHz range. The MMIC combines a T/R switch, low-noise amplifier, and a power amplifier. The receive path has dual-outputs which offer 21dB gain and 2.7dB noise figure. The transmit path delivers 4W of saturated power with 23dB large signal gain. The FEM is robust up to 4W of input power into the ANT port eliminating the need for a limiter.

  3. CATV Hybrid Power Double Amplifier Module: QPA3250 12/3/2018

    Qorvo’s QPA3250 is a hybrid power double amplifier module ideally used for Node+x and deep fiver node systems and CATV amplifier systems operating in the 45 – 1218 MHz range. Employing a GaAs pHEMT die and GaN die, the part offers extremely high output up to 76.8 dBmV composite power or 67 dBmV virtual level power.

  4. 26 – 30 GHz, 1W GaN Front End Module: QPF4001 11/28/2018

    The QPF4001 from Qorvo is a multi-function GaN MMIC front-end module (FEM) ideally utilized for 28 GHz phased array 5G base stations and terminals. This device operates over the 26 to 30 GHz frequency range, and combines a low noise, high linearity LNA, a low insertion loss, high isolation TR switch, and a high gain, high efficiency multi-stage PA.

  5. 4.4 – 5.0 GHz GaN Power Amplifier Module: QPA4501 9/4/2018

    Qorvo’s QPA4501 is an integrated 2-stage Power Amplifier (PA) module designed to cover the frequency range of 4.4 to 5.0 GHz. This device is optimized for 5G massive MIMO, W-CDMA/LTE, macro and micro cell base station, active antenna, and other general purpose applications.

  6. 2.4 GHz Wi-Fi/BT/LTE Co-Existence BAW Filter: QPQ1907 9/4/2018

    Qorvo’s QPQ1907 is a high-performance, high power Bulk Acoustic Wave (BAW) band-pass filter designed to enable coexistence of WiFi and LTE signals within the same device or in close proximity to one another. This device is ideally used in WiFi/Bluetooth, consumer premise equipment (CPE), small cells, and smart meter applications.

  7. Qorvo® MatchCalc™: An Introduction Tutorial 3/19/2018

    Qorvo® MatchCalc™ is the future in online downloadable tools, capable of a wide range of RF matching tasks.

  8. Qorvo® MatchCalc™: How To Use Snapshot And Markers 3/19/2018

    This video provides a brief tutorial on how to use the Snapshot and Markers functions on a MatchCalc™ plot.

  9. High-Power Switch LNA Module: QPB9325 11/20/2017

    Qorvo offers the QPB9325 highly integrated front-end module with operation in the 3.6 – 3.8 GHz frequency range ideally suited for TDD base station, wireless infrastructure, and macro or picocell base station applications. This LNA module integrates RF functional blocks such as a pin-diode based high power switch along with two LNA stages.

  10. Ultra-Low-Noise Flat Gain LNA: QPL9503 5/4/2017

    The QPL9503 from Qorvo is a flat-gain, high-linearity, ultra-low-noise amplifier (LNA) optimized for the 3.0 – 6.0 GHz frequency range. At the 5.5 GHz frequency mark, this LNA typically provides 21.6dB gain, 45.5 dBm OIP3 at 56 nM bias setting, and 0.95 dB noise figure. Biasing is also possible from a single positive supply ranging from 3.3 to 5 volts.